Blomberg DW24100B Manuel d'installation

Installation ManualDishwasherFOR MODELS (ADA Height)DW 24100 BDW 24100 SSDW 24100 WDW 25200 BWSDW 25200 SSWSUSADW 25200 WWSDW 55100 BDW 55100 FBIDW 55

7USA321/4 - 341/4(819mm - 870mm)115/16(50mm)6.3.1 INSTALLING THE FOOT SUPPORTSSupplied (4)115/16(50mm)321/4 - 361/4(819mm - 920mm)115/16(50mm)1

8USAT20Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height.Adjust the rear foot level wi

9USA6.5 PREPARING THE WATER CONNECTION (A)Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections

10USA6.6 DRAIN PREPARATIONThe dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice :Either one o

11USAA6.7 STEAM PROTECTION FOILSteam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it

12USA7. PLACEMENT OF DISHWASHER INTO THE OPENINGNow place the dishwasher into the opening and get ready to connect all hoses and electrical connection

13USA7.1.2 WATER SUPPLY CONNECTIONWater supply may be connected to the dishwasher in one of two ways:With metal braided hose.• With copper tubing.• 7.

14USAØ 1/8" (3,5mm)Ø 1/8" (3,5mm)ABC7.3 READJUSTING FOOT LEVELSNow that the dishwasher is in the cabinet you must readjust the feet to bring

15USAABstCoAstCBopAstCBorLock the toe kick brackets as shown with the plastic tab in the figure C by pushing the plastic tab on the dishwasher into th

16USA??A6 1/10(155mm)C155mmMid. PointMax : 12,1 lb (5,5 kg)7.5 INSTALLING THE OUTER DOOR(DW 55100 FBI)Measure the height and width of the enclosure

Installation Manual For Dishwasher ModelsStart / PauseTime DelayCycle SelectHalf Load /TabletDW 24100 BDW 24100 SSDW 24100 WDW 25200 BWSDW 25200 SSWSD

17USAAx4vØ 1/8" (3,5mm)B5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure A).6. Mount

18USACØ 3/16" (4mm)yx4ABØ 3/16" (4mm)yx4C7. Open the door and remove the two caps and two screws inside the door at position 1 and 3 (Figure

19USAAB0 kgC11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A).11.1. If the door hits the toe kick cut the necessar

20USAØ 1/8" (3,5mm)1 9/1640mmAd3/8 (10mm)21 7/16(544mm)CBDBCA Notice :If you have a European kitchen or want to install a wooden toe kick to m

21USA8. INSTALLER CHECKLISTYour installer must have completed and checked the following:The dishwasher is square and level.• The dishwasher is fastene

17 9066 01 00-AC-USA

Contents1. IMPORTANT SAFETY INSTRUCTIONS 11.1 INSPECT THE DISHWASHER 21.2 HOW TO CONTACT US 22. TOOLS WHICH MAY BE NEEDED 33. MATERIALS WHICH MAY

1USACAUTIONWARNINGÝNoticeINTRODUCTIONPlease read this installation manual and particularly the safety instructions completely and carefully. They will

2USADishwasher must be secured to adjacent • cabinetry using the brackets provided. Failure to do this may cause damage to property or bodily injury.C

3USA2. TOOLS WHICH MAY BE NEEDED3. MATERIALS WHICH MAY BE NEEDED(Additional materials may be required to comply with local codes)Hot Water Supply Line

4USAx1x1n.x4m.x1x2x2a.b.d.e.f.g.h.c.j.k.l.o.p.s.t.v.y.r.z.x1x1x1x1x6x1x1x1x1x1x1x2x4x1x14. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts for your dishwash

5USA5. DISHWASHER SPECIFICATIONS321/4-361/4(819mm - 920mm)24(610mm)24(610mm)239/16(598mm)24 max(610mm max)321/2 - 361/4(825mm - 920mm)5.1 TECH

6USA6. ENCLOSURE PREPARATION6.1 ELECTRICAL PREPARATION WARNINGThe dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a