Blomberg DWT 34410 ULTRA Manuel d'installation

USAInstallation ManualDishwasherFOR MODELSDWT 14210 NBL00DWT 14220 NBL00DWT 14240 NBL00DWT 15210 NBL00DWT 15220 NBL00DWT 15240 NBL00DWT 15211 NBL00DWT

7USA6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETSBBAA WARNINGDishwasher must be secured to adjacent cabinetry using the mounting brackets provided.

8USAAdjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height.Adjust the rear foot level with

9USA6.5 PREPARING THE WATER CONNECTION (A)Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections

10USA6.6 DRAIN PREPARATIONThe dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice :• Either on

11USA7. PLACEMENT OF DISHWASHER INTO THE OPENINGNow place the dishwasher into the opening and get ready to connect all hoses and electrical connection

12USA7.1.2 PREPERATION OF WATER SUPPLY & ELECTRICAL CONNECTIONSAABBCCDDLeft side water supply connectionRight side electrical supply connectionBef

13USAFEFGGAfter installing one clip for each side push the dishwasher into the cabinet (Figure E).Note that while pushing the dishwasher into the cabi

14USA7.1.3 WATER SUPPLY CONNECTIONWater supply may be connected to the dishwasher in one of two ways:• With metal braided hose.• With copper tubing. C

15USAABCDInstall a strain relief (not supplied) into the opening on the kick plate. (Figure A)Pass the electrical supply cable through the strain reli

16USA7.3 ADJUSTING THE MOVABLE TOE KICKNow that you have successfully installed the dishwasher, you need to attach the toe kick to the dishwasher. Th

Installation Manual For Dishwasher ModelsDWT 15211 NBL00DWT 15221 NBL00DWT 15241 NBL00DWT 14210 NBL00DWT 14220 NBL00DWT 14240 NBL00DWT 15210 NBL00DWT

17USABstCAoAstCBopIf the enclosure height is below 331/16” (840mm) use only “o” labelled toe kick (toe kick without slots). Installation should be don

18USABAA8 11/16(221,2mm)AA8 11/16(221,2mm)8 11/16(221,2mm)2. Remove the plastic mounting brackets from the dishwasher (Figure B).B3. Lay the schema

19USAx4vCØ 1/8" (3,5mm)AX8B5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure C).6. Cut

20USAyx4AØ 3/16" (4mm)Byx4CØ 3/16" (4mm)10. Using the four screws Ø 3/16” x 111/16” (Ø 4mm x 43mm) provided, attach the wooden door to the d

21USAAB0 kgC13. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A).13.1. If the door hits the toe kick cut the necessar

22USAØ 1/8" (3,5mm)1 9/1640mmdA21 7/16(544mm)3/8 (10mm)BDCBCA Notice :If you have a European kitchen or want to install a wooden toe kick to m

23USA8. INSTALLER CHECKLISTYour installer must have completed and checked the following:• The dishwasher is square and level.• The dishwasher is fas

17 1844 01 00 00-USA

Contents1. IMPORTANT SAFETY INSTRUCTIONS 11.1 INSPECT THE DISHWASHER 21.2 HOW TO CONTACT US 22. TOOLS WHICH MAY BE NEEDED 33. MATERIALS WHICH MAY

1USACAUTIONWARNINGÝNoticeINTRODUCTIONPlease read this installation manual and particularly the safety instructions completely and carefully. They will

2USAbe met to prevent injury and machine damage. Consult a qualified electrician if in doubt.• Do not use any extension cord or portable outlet device

3USA2. TOOLS WHICH MAY BE NEEDED3. MATERIALS WHICH MAY BE NEEDED(Additional materials may be required to comply with local codes)Hot Water Supply Line

4USAx1x1a.b.d.e.f.g.h.c.x1x1x1x1x6x1x2x2j.k.l.m.o.p.s.v.u.7 3/4(196,5mm)y.n.r.t.x1x1x1x3x1x1x4x1x4x4x24. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts fo

5USA5. DISHWASHER SPECIFICATIONS(861mm - 911mm)24(610mm)24(610mm)239/16(598mm)24 max(610mm max)34 - 361/4(864mm - 920mm)33 7/8- 35 7/85.1 TECHN

6USA6. ENCLOSURE PREPARATION Notice :• For proper dishwasher operation and appearance ensure that the enclosure has the minimum dimensions shown in t